paver-sealing

Concrete Sealer, Concrete Coatings, and Paver Sealer

The process of protecting a concrete surface from the elements is called sealing. Concrete coatings or sealers can be applied to new or old concrete surfaces for a variety of reasons. They protect the surface from damage caused by erosion and UV rays which break down the material causing deterioration over time. 

By protecting the surface sealers can also help prevent stains and chemical spills from absorbing into the concrete. Concrete sealers are available in a variety of strengths and durability ranging from single use to industrial applications which need to be refreshed periodically.

Concrete sealers and coatings are used to protect new or old concrete surfaces from damage caused by erosion, stains, chemical spills and UV rays. Sealers add a protective layer between the surface and anything that may come in contact with it such as chemicals, liquids, dirt and much more. Concrete coatings offer much stronger protection from chemicals, stains and UV rays than sealers. Coating is the best choice for extreme conditions like chemical spills.

Sealing vs. Coating: What’s best for my project?

Sealing adds a protective layer on top of the concrete.

A coating is more durable than a , offering protection from chemical spills and other difficult substances. Concrete coatings offer much stronger protection than penetrating sealers. Sealers are often used to protect light colored or stained concrete surfaces while providing easy clean up. Coatings are ideal for extremely tough conditions such as chemical spills and oil spills.

paver-sealer
seal-pavers

How do I maintain my concrete sealer or coating?

Concrete sealers and coatings need to be maintained on a regular basis to ensure even coverage. In order to maintain the coating, it is recommended that you wait for heavy rain storms before applying additional coats of sealer or re-coating. This will allow water pressure to push any old residue off the surface. 

If the concrete is stained, it is best to scrub off any stains with a neutral cleaner then apply new sealer or coating for maximum protection.

Sealing concrete is easy to maintain by simply rinsing off your concrete surface with a garden hose after exposure to heavy rain, snow or ice. If you are looking for more protection from the elements be sure to reseal every couple of years.

How frequently should I seal my new concrete?

Sealing your new concrete after 30 days or after it has properly cured is one of the most important steps you can take in protecting it. You should immediately seal concrete that has just been power washed to ensure maximum protection. If you don’t seal your concrete immediately, there are still other protective measures you can take to protect your investment.

concrete-pavers
concrete-paver-sealer

What are the different types of concrete sealers?

There are two basic types of concrete sealer: penetrating and film forming. Film forming sealers have a tendency to darken and enhance the color of pavers, stamped concrete, brick paver blocks, limestone slabs, bricks and other natural stones. Film forming sealers will work on just about any concrete or natural stone surface that is porous. 

To distinguish between the two, place a drop of water on each surface and let it stand for one minute. Film forming sealers will create a film over the puddle of water while penetrating sealer will absorb into the concrete or stone.

What are the different types of concrete sealers?

There are two basic types of concrete sealer: penetrating and film forming. Film forming or film-forming sealers have a tendency to darken and enhance the color of pavers, stamped concrete, brick paver blocks, limestone slabs, bricks and other natural stones. 

Film forming sealers will work on just about any concrete or natural stone surface that is porous. To distinguish between the two, place a drop of water on each surface and let it stand for one minute. Film forming sealers will create a film over the puddle of water while penetrating sealer will absorb into the concrete or stone.

paver-sealer

How many coats of concrete sealer do I need?

You will need one coat of sealer will cover anywhere from 200 to 500 square feet per gallon depending on the porosity of the substrate being sealed. Apply the first coat and allow it to dry, then apply a second coat according to the manufacturer’s directions.  Please contact us directly at 813-309-9202 prior to sealing with any questions or concerns regarding sealing your concrete, brick paver, or natural stone surface.

How do I clean my concrete once it’s been sealed?

For best results we recommend using a mild degreaser such as Purple Power or Gold Assassin. The manufacturer advises that you wear protective gear such as rubber gloves and goggles when cleaning. Dilute the degreaser per the manufacturer’s directions and apply with a deck brush or pressure washer (if using a pressure washer use medium/high setting). Rinse thoroughly with clean water to ensure all residue has been removed.

long will my sealer last? Concrete Sealers can last anywhere from 1-5 years for a film-forming sealer and can last a life span of the substrate for penetrating sealers depending on the manufacturer you choose. We recommend that you re-seal once every two years to ensure even

clean-and-seal-concrete

How to Clean and Seal Concrete

Proper cleaning procedures are essential if you want your new concrete surface to stay protected. High pressure washing the concrete before applying a concrete sealer will give the best results. 

It is also important to choose a quality concrete sealer that adheres to the surface or a penetrating sealer that provides long lasting protection. Most professional concrete sealing services recommend re-applying the sealer every few years to keep your surface protected from water, oil and other substances that can harm your concrete.

What are the specific jobs that sealers or coatings can be applied to?

Sealers and coatings can be applied to concrete surfaces after the concrete has cured. Sealers are best for light duty applications such as decorative concrete, pool decks, garage floors and much more. Water based film forming coatings and sealers can be applied to almost any damp surface including slabs, walkways, exterior walls, and decorative concrete among others.

sealer-for-pavers
concrete-sealers

Sealing vs. Coating: What’s best for my project?

Concrete sealers and coatings are used to protect new or old concrete surfaces from damage caused by erosion, stains, chemical spills and UV rays. Sealers add a protective layer between the surface and anything that may come in contact with it such as chemicals, liquids, dirt and much more. 

Film forming coatings offer much stronger protection from chemicals, stains and UV rays than penetrating sealers. A film forming coating is the best choice for extreme conditions like chemical spills.

Sealers and coatings are used to protect concrete surfaces from the elements.

Film forming concrete coatings are designed to offer superior protection from staining, weathering and chemical spills.

Sealers can last anywhere from 1-5 years depending on the manufacturer you choose. We recommend re-sealing every two years for best results.

What is the difference between concrete sealers and concrete coatings?

Concrete coatings are designed for extreme conditions such as chemical spills, stains or weathering. They offer superior protection from staining, dirt, oil and other harmful substances that can harm your concrete. Concrete sealers are used to protect new or old concrete surfaces from damage that can be caused by erosion, stains, chemical spills and UV rays. 

They add a protective layer between the surface and anything that may come in contact with it such as chemicals, liquids, dirt and much more. Coatings offer much stronger protection from chemicals, stains and UV rays. 

Sealers are best for light duty applications such as decorative concrete, pool decks, garage floors and much more. Coatings can be applied to almost any wet surface including slabs, walkways, exterior walls and decorative concrete among others.

concrete-coatings
concrete-sealer-last

How long does concrete sealer last?

Film forming concrete coatings are designed to last anywhere from 2-10 years depending on the manufacturer you choose and conditions, such as the elements, foot or vehicular traffic, and how much sealer was applied.We recommend re-sealing every few years for best results. 

Penetrating concrete sealers can last anywhere from 1-5 years or up to the lifespan of the substrate depending on the manufacturer you choose. We recommend re-sealing every two years for best results.

What is concrete sealer made of?

Concrete sealers are available in a variety of strengths and durability ranging from single use to industrial applications which need to be refreshed periodically. Concrete coatings can be made from silicone, acrylic and urethane depending on the manufacturer you choose. The main ingredient is usually one of these three substances or a combination thereof.

How do you repair cracks in concrete sealer?

Film forming concrete coatings are polymeric-based and add a layer of protection to the surface. They don’t add any structural support or strengthen the surface like penetrating concrete sealers do, they simply protect it from anything that may come in contact with it such as chemicals, liquids and dirt. 

If the surface was compromised before coating it then applying another coat won’t work. You will need to remove the coating and reseal the surface with a that contains polymers in order for it to bind properly with the cracked area, sealing it from water or other substances making contact with it.

How frequently should sealers and coatings be reapplied for continued protection?

Sealers should be applied to new concrete once it has cured for at least 30 days. If you apply it prior to curing the surface will stay tacky and not properly bind with the sealer causing it to do its job effectively. You should reapply every 1-2 years for your best protection against erosion, chemicals, stains and other environmental conditions. 

Concrete coatings should be reapplied every 2-5 years for a stronger application. This can vary depending on the manufacturer you choose and the specific location of your surrounding environment where it is being applied. For example, a coating in a residential area will last much longer than a coating in a harsh industrial environment because the former may need to be refreshed more often.

What are the different types of concrete sealers available?

Concrete sealers are available in two main types: penetrating and film forming. Penetrating concrete sealers actually form a chemical bond with the surface it is applied to, strengthening it and protecting it from any type of damage such as erosion, chemicals, UV rays and more. Film forming coatings absorb into the pours of the concrete adding another protective layer between the surface and anything that may come in contact with it such as chemicals, liquids, dirt and much more. 

Coatings offer much stronger protection from chemicals, stains and UV rays. Penetrating sealers are best for light duty applications such as decorative concrete, pool decks, garage floors and much more. Film forming coatings can be applied to any concrete surface for a strong protection against chemicals, stains and other environmental factors.

How frequently should sealers and coatings be reapplied for continued protection?

Sealers should be applied to new concrete once it has cured for at least 30 days. If you apply it prior to curing the surface will stay tacky and not properly bind with the sealer causing it to do its job effectively. You should reapply every 1-2 years for your best protection against erosion, chemicals, stains and other environmental conditions. 

Concrete coatings should be reapplied every 2-5 years for a stronger application. This can vary depending on the manufacturer you choose and the specific location of your surrounding environment where it is being applied. For example, a coating in a residential area will last much longer than a coating in a harsh industrial environment because the former may need to be refreshed more often.

concrete-paver-sealer

How do I know what type of sealer to buy?

Know the environment you are going to be applying it to. Penetrating sealers usually come in one gallon sizes which is enough for around 200-250 square feet per gallon depending on the porosity of the concrete. Film forming sealers can be applied to any surface and come in 5 gallon pails which averages around 800-1000 unless of course you’re using SealThane which averages 1500-2000 square feet per 5 gallon pail. square feet of protection depending on the porosity of the surface it is being applied to. 

If you have more than one type of sealer and only need to buy one, penetrating sealers will offer a stronger application for light duty applications and film forming concrete coatings will offer stronger protection for heavy industrial applications.

How do I apply concrete sealers?

Read the specific instructions on apply each product you are using, but generally speaking most penetrating sealers come in a ready-to-use form which you simply pour it out of the container and spread it across the entire area you are going to be applying it in. After covering the area in a thin coat, wait for it to dry then apply another coat in the same manner. Film forming concrete sealers come in a concentrated form which needs to be applied using a pump sprayer or garden sprayer for larger areas.

The concrete sealer should be applied in a thin even coat to the entire area but take caution not to apply it too thickly otherwise you will form puddles. After the entire area has been covered let it sit for 15-30 minutes depending on how fast it dries then start back at the beginning and move the sealer around with a leaf blower or push broom for consistency. 

After you have brushed the excess, wait another 2-3 hours before putting any type of foot traffic on it to prevent slipping, 24 hours is better. Remember that concrete sealers are essentially a film forming application to the surface so you should never mix them with other chemicals or cleaners. If you do, they will react in unpredictable ways and could actually dissolve the concrete itself over time.

What kind of concrete sealer will work best for my project?

There is no concrete sealer which will work best for all projects. It really depends on what the project entails and how long it needs to last. If you are looking for a strong protection from environmental factors such as chemicals, stains, and UV rays then you should opt for a film forming concrete sealer whereas if your project only involves light duty applications such as decorative concrete, pool decks or garage flooring then a penetrating sealer is what you should look for. To learn more about our concrete coatings please visit our online store at www.paversealercompany.com. If you have any questions please feel free to contact us directly, either through the website, 813-445-8065 or  at support@paversealercompany.com. Good Luck!

concrete-patio-sealer

How can I find a concrete paver sealer?

On the Internet! The only place to find good quality concrete paver sealers is through Internet sales due to its wide variety of products. Walk down any street and you will see a sign for a local paint and hardware store which isn’t bad, but I can assure you that they don’t have nearly as many options in regard to the type of concrete paver sealers, quality of the sealer or even price. The reason for this is because you are paying for their overhead costs which includes rent, labor and taxes so they have to turn a large profit in order to keep up.

Online retailers don’t have these restrictions so they can charge much less while still being able to sell quality concrete paver sealers. Online retailers are also taking advantage of the fact that there are enough people who are sick and tired of dealing with over-priced concrete paver sealer salesmen or big box stores which is why they include free shipping, money back guarantees and other incentives to attract new customers to their stores. So if you want good quality concrete at the best possible price, check out our website – www.sealermart.com – and start shopping for your new paver sealer online.

How do I apply a concrete paver sealer onto pavers?

Using a battery-operated sprayer or pump-up sprayer is usually how new concrete paver sealers are applied to pavers. First you should review the instructions on the back of the product you are using for any special instructions. The most basic concrete paver sealer can be applied just like regular paint, but others may need to be diluted or mixed with water before it is applied. If you are using a roller then apply enough sealer so that it will cover the entire area in one pass of the roller, if it takes two rolls to do the entire area, then apply it in two passes.

If you are using a brush for smaller areas such as cracks and corners make sure that your applicator is stiff enough to get deep into the crevices without causing damage or leaving streaks after you are done. Allow the sealer to dry for at least 24 hours hours before walking on your newly sealed concrete paver sealer. Know that if you are using a penetrating sealer, it will still happen fairly quickly but may take up to an hour for it to become rainproof and 72 hours to fully cure. It is always best to er on the side of caution and wait until the next day before walking or driving on newly poured concrete paver sealers.

paver-joint-sealer

How do I clean my concrete paver sealer?

If you are using a film forming sealer then it is best to just wash your pavers with soap and water or use a mild degreaser for stubborn stains. If there is any dirt or grime stuck to the surface of your concrete paver sealer then use a gentle detergent mixed with water which you can then rinse off with a hose. If you are using a penetrating sealer then it is best to use a pressure washer as they can get deep into the concrete and clean them without causing damage or draining them of any protective qualities.

You should never allow your concrete pavers to become dirty, but if dirt occurs then you can scrub them down with a stiff-bristled brush and some soap and water.

What is the difference between concrete paver sealer and concrete coating, and which one should I use?

There are many different types of concrete paver sealers available for purchase online but there are even more when it comes to concrete coatings. When it comes to concrete paver sealers, they generally fall into two types: penetrating or film forming. Penetrating sealers seep deep into the pores of the concrete and provide a lasting protection which can last anywhere from several years to several decades, even up to the lifespan of the substrate. Film forming sealers are applied like paint and provide a decorative look for your concrete pavers. The type of look you are going for will determine if a film forming or penetrating sealer is best for your situation.

Concrete coatings are generally very thick and glossy looking, making them perfect for waterproofing applications such as pools, bathrooms, kitchens etc. Other concrete coatings can be used to insulate the surface of the concrete by providing a thermal barrier such as in industrial applications.

What is the best concrete paver sealer to use on tennis courts?

The best concrete paver sealers for tennis courts are generally film forming sealers or self-leveling coatings which will provide a decorative look and protect against things like scuffing, staining etc. Tennis court concrete paver sealers are often used with decorative concrete overlay systems which can be easily applied to concrete surfaces. Such decorative concrete overlay systems come in the form of overlays, stains, and accented chips.

concrete-paver-sealer

Should I re-seal or re-coat existing concrete surfaces to prevent damage from erosion, stains, and chemicals?

You should always re-seal or re-coat existing concrete surfaces to prevent damage from erosion, stains, and chemicals. Erosion is caused by the material being exposed to elements without any protective coating or paver sealer so it is best to maintain your concrete pavers with a film forming sealer which can be easily reapplied when necessary.

Film forming sealers also provide a protective barrier against stains and chemicals which can be harmful to your concrete paver sealers. Concrete coatings are the best choice when it comes to protecting existing concrete pavers from erosion, stains, and chemical spills because they work on more than just the surface of the material.

What is the longest lasting concrete paver sealer?

The longest lasting concrete paver sealers are generally penetrating ones because they seep deep into the pores of the concrete which helps prevent things like water absorption, stains, and erosion. Penetrating sealers also allow for very little maintenance on the part of the property owner as they require no reapplication or special care.

Why should I hire a concrete sealing professional?

Hiring a concrete paver sealing professional is recommended because it can be very difficult to determine if you are using the right type of paver sealer or even application methods for your pavers. Also, there are several different types of concrete paver sealers available so getting an expert view on which one is best for your specific application could save you time, money, and energy. It is important to note that concrete paver sealers are only one part of a larger process for maintaining your pavers.

When should I re-seal my pavers?

Pavers require attention year round but are particularly vulnerable in the winter months when their surface becomes exposed to harsh elements like rain, ice and snow. Concrete paver sealers are most applied in one of two situations: before installation or after installation. Sealing pavers before they are installed is the best way to prevent staining or sinking that can occur when high volumes of water enter the pores of the concrete but aren’t properly drained.

What is a good low cost concrete paver sealer?

Low cost concrete paver sealers are generally film forming or even decorative concrete coatings which can be applied to existing pavers. They provide the best protection against things like staining, scuffing and chemical spills by providing a protective barrier. Decorative concrete coatings can provide an elegant look to your concrete pavers and may even require less maintenance than other types of paver sealers.

What is the best way for me to remove stains from my concrete pavers?

The most effective and efficient way to remove stains from concrete pavers is by using a concrete paver cleaning product which works to remove the stain while protecting the paver sealers. Removing stains without damaging the paver sealer requires special consideration, particularly when it comes to removing things like oil or wax which can permanently damage your pavers if mixed with cleaning products.

 How long will my concrete paver sealer last?

Paver sealers will last anywhere from 1-5 years depending on the type of paver sealer and quality. It varies for every application but it’s important to note that even if your concrete paver sealers are showing signs of wear you can always reapply them yourself or hire a professional. Concrete coatings generally last longer than film forming ones because they provide a protective coating that can’t be removed by chemicals or cleaners.

How long do I have to wait before putting down pavers?

There’s no specific waiting period for installing pavers after applying paver sealers because the sealer doesn’t interfere with the installation process itself. Depending on your application you may want to wait a day or two before putting down pavers because placing them immediately after application may cause the paver sealer to become hazy.

How long do concrete pavers last?

The lifespan of concrete pavers varies between 20 to 50 years but they won’t last forever. Pavers require proper maintenance and care in order to last the full life cycle. One of the most important things to take into consideration when caring for your pavers is paver sealing which protects the concrete from damage caused by erosion, chemicals and UV rays. Concrete paver sealers are available in a variety of strengths and durability ranging from single use to industrial applications which need to be refreshed periodically.

Are concrete paver sealers really necessary?

The answer to “are concrete paver sealers necessary” is YES. Concrete pavers are vulnerable to the elements without proper care and maintenance. Sealing your concrete pavers protects them by preventing damage caused by erosion, chemicals and UV rays while also providing an extra layer of protection against things like staining and scuffing.

How do I clean my concrete pavers?

Proper care for your concrete paver sealer starts with cleaning them on a regular basis. The best way to keep your pavers looking like new is by using a paver cleaning product like or a mild degreaser like Purple Power which can remove stains while protecting the concrete paver sealer. Using a product that’s strong enough to remove stains from concrete can also damage your paver sealer so it’s important you only use the right products when cleaning your pavers.

Do I need to remove any existing concrete surface before applying a new concrete coating or sealer?

If you’re applying a new concrete coating or paver sealer over existing ones it’s important to remove the old product before starting. Old concrete coatings and paver sealers contain contaminants which can mix with the new products causing them to become hazy or damage your pavers.

Generally, you can apply a new water based paver sealer over a previously applied water based paver sealer.  Conduct a test for compatibility by applying the new paver sealer over the existing paver sealer in a small inconspicuous area and let dry for 24 hours.  This is a test to ensure compatibility.  You are testing for hazing, whiting, and poor adhesion.  If any of these issues occur, the old paver sealer must be removed.  Using a product like NPS RX Paint Stripper can make light work out of removing a previous or existing coating.

How do I prepare for applying a concrete paver sealer?

Proper application of a concrete paver sealer starts with proper preparation. Getting your concrete surfaces ready for sealing is the first step to protecting your pavers. You’ll want to sweep or vacuum up any debris and remove all oils, plants and bugs and pressure wash the area to be sealed before applying any sealers so you don’t apply them on top of contaminants or damage the sealer.

How do paver stains get on pavers?

Paver stains happen, but they’re easily preventable with proper care and maintenance of your paver surfaces which includes concrete paver sealers. Stains tend to be caused by some kind of chemical that’s spilled onto the surface which then gets absorbed into the concrete. Other types of stains can also be attributed to minerals and mold which grow when water gets trapped in between pavers and isn’t allowed to evaporate through the surface.

What is pigmented concrete?

Pigmented concrete or stained paver sealer is a special type of sealer used for decorative concrete pavers. These products come in a large variety of colors which can be used to create beautiful designs on concrete paver surfaces. They’re available in the form of dyes, paints and stains which are mixed with clear or tinted sealers to protect them from damage caused by chemicals and UV rays.

Why should I choose to use a single use sealer instead of an industrial application?

For most concrete pavers, single component paver sealers are the best option, and the easiest to use, for providing an extra layer of protection against chemicals and UV rays while also improving stain and chemical resistance. Single use concrete paver sealers tend to last less than two component paver sealer applications and leave less mess making them ideal for smaller projects. If you’re looking for a quick solution or a product that can be applied in the winter season, single use paver sealers like Paver Seal RX are a great choice.

How do I get rid of mold and mildew on concrete?

Getting rid of mold and mildew from concrete surfaces starts with proper care and maintenance which includes using the right products to remove it from your pavers. There is a wide variety of mold and mildew remover products available in the market which can be applied directly to your paver surface. These products contain chemicals that kill mold spores, but they can also remove the sealer leaving you with an unprotected surface which can then result in more stains or damage.

It’s important to find a chemical like chlorine that can be used to kill mold and algae without damaging the paver sealer coating.  A mild degreaser that can be used also to kill organics is the best choice.

How do I know which concrete sealer is best for my job?

Choosing the right concrete paver sealer for your job depends on a number of factors which include the type and nature of your project and budget. It’s important to first determine which kind of product you need: A single component or two component concrete paver sealer like SealThane. And then look at the other key specifications such as durability, color retention and resistance to chemicals before making your final decision.

What is the best way to apply concrete sealer?

Applying concrete paver sealers is an easy process which involves simply following the manufacturer’s instructions on the label before you start or calling us directly at 813-445-8065 for tailored directions or product technical support. These products are made to be applied with either a sprayer or roller applicator and can be used alone or in combination with other sealing products for added protection. Choosing the right applicator will depend on your project and how much work you need to do.

How long does concrete paver sealer last?

The exact lifespan of concrete paver sealers can vary depending on a number of factors but most last up to 2-5 years when applied correctly. Most single component paver sealers tend to last less time than two component applications which require less frequent reapplication. Keeping in mind how much work you’re putting into sealing your concrete pavers, the cost of having them resurfaced or resealed won’t come as a surprise after all.

What are the different types of concrete sealers available?

Concrete sealers are available in different forms which include stains, dyes, single component or two component applications depending on the type of surface they’re used on. Some paver sealers also come with the option of tinting for added color and protection while others provide enhanced resistance to staining.

What is the difference between water based, solvent based and acrylic coatings?

There are three types of concrete paver sealers available: water based, solvent based and acrylic. Each of these products is designed to provide a different level of protection and has its own benefits depending on the type of project you’re working on. Concrete coatings made with water typically require fewer coats than their solvent and acrylic counterparts and dry faster.

What is the difference between concrete paver sealer and concrete stain?

Concrete stains come in a variety of colors and provide a permanent solution for adding a new layer of protection to your concrete surface. They tend to last much longer than other kinds of stains but do require regular reapplication. Sealers, on the other hand, do not fade and can be added to stained concrete surfaces to provide a richer color.

How do I clean my paver sealer after application?

The first thing you need to know is that it’s never a good idea to use any sort of acid or alkaline cleaner on your concrete pavers as they may damage the sealer and your paver’s surface. The best way to clean a paver sealer is by simply washing it with warm soapy water which you can do by hand or using a pressure washer. This will get rid of any dirt, dust, or debris without compromising on the protection of your paver’s surface.

How frequently should sealers and coatings be reapplied for continued protection against damage such as erosion, chemicals, stains and UV rays?

Two component paver sealer applications will need to be reapplied less frequently than single component paver sealers depending on the intensity of work they’re put through. However, most can last anywhere from a year to three years before requiring reapplication.

What is micro-topping and what are its benefits?

Micro-topping is a layer of paver sealer which is applied over the top of an existing concrete paver coating. It adds color and more protection against staining, making it a great option for commercial spaces such as parking lots or shopping malls which deal with grease and oil stains.

Are concrete paver sealers necessary? How do I clean my concrete paver sealer? What is the longest lasting concrete paver sealer?

Concrete sealers are an important part of protecting your concrete surface from damage caused by erosion, chemicals, stains, and UV rays. It’s also crucial to keep in mind that not all concrete paver sealers are created equal, and some may be better suited for your project than others depending on the types of work they’re put through. Keeping these things in mind will help you make an informed decision about what paver sealer is best for your needs.

Please contact us at 813-445-8065 or through or website by clicking here for more information and advice about your concrete or concrete paver sealing job! Our team members are standing by.